课程信息

首页 Search Courses CIDEX Open Courses Online Guide (Lecturer) Online Guide (Student)

🌟 Welcome to Your New UniKL VLE ! 🌟 We’ve made these improvements to ensure your learning experience is engaging, flexible, and more enjoyable than ever! 🎉

PDP02903 - INTRODUCTION TO ENGINEERING DRAWING

教师: Mohamad Nor AzliMuhamad Syafiq bin

Skill Level: Beginner

Announcements

CLP PDP02903

Chapter 2

Chapter 3

Chapter 4

1.Parellel Line

Drawing vertical line

Bisecting line

Bisecting an angle

Constructing 60’ angle

Constructing a 30’ angle

Constructing a 90’ angle

Constructing a 45’ angle

1. square with a given side length.

2. Constructing a square given its diagonal.

3. Constructing a rectangle given its diagonal and one side (30 mm).

4. Constructing a rhombus given its diagonal and side length (60 mm).

5. Constructing a parallelogram given one side (50 mm) and one angle (60°).

6. Constructing a trapezoid given the parallel side (30 mm), vertical height, and two angles (60°).

1. Constructing an equilateral triangle given the side length.

2. Constructing a triangle given the length of each side (BC = 75 mm and AC = 85 mm).

3. Constructing an isosceles triangle given the base length and height (70 mm).

4. Constructing a triangle given two side lengths (AB) & (AC = 60 mm) and a base angle (∠BAC = 60°).

5. Constructing a triangle given the base length, height (AC = 75 mm),and one base angle (∠BAC = 75°).

6. Constructing a triangle given the base length and both base angles (∠ABC = 48° and ∠BAC = 32°).

1. Constructing a circle passing through three given points.

2. Constructing an inscribed circle within a triangle.

3. Constructing a circumscribed circle.

4. Constructing a circumscribed circle outside a triangle.

1. Constructing a regular pentagon given the side length

2. Constructing a regular pentagon inside a circle given the diameter.

3. Constructing a hexagon given the diameter.

4. Constructing a hexagon given the center dimension.

5. Constructing a regular heptagon given the constraint dimensions.

6. Constructing a regular octagon given the diagonal dimension.

PDP02903 - INTRODUCTION TO ENGINEERING DRAWING

常规

Announcements

CLP PDP02903

CLP PDP02903

Engineering Drawing Exercise

Chapter 2

Chapter 3

Chapter 4

TUTORIAL VIDEO GEOMETRICAL CONSTRUCTION

1.Parellel Line

Drawing vertical line

Bisecting line

Bisecting an angle

Constructing 60’ angle

Constructing a 30’ angle

Constructing a 90’ angle

Constructing a 45’ angle

TUTORIAL VIDEO QUADRILATERAL (DRAWING NO. 3)

1. square with a given side length.

2. Constructing a square given its diagonal.

3. Constructing a rectangle given its diagonal and one side (30 mm).

4. Constructing a rhombus given its diagonal and side length (60 mm).

5. Constructing a parallelogram given one side (50 mm) and one angle (60°).

6. Constructing a trapezoid given the parallel side (30 mm), vertical height, and two angles (60°).

TUTORIAL VIDEO TRIANGLES (DRAWING NO.4)

1. Constructing an equilateral triangle given the side length.

2. Constructing a triangle given the length of each side (BC = 75 mm and AC = 85 mm).

3. Constructing an isosceles triangle given the base length and height (70 mm).

4. Constructing a triangle given two side lengths (AB) &amp; (AC = 60 mm) and a base angle (∠BAC = 60°).

5. Constructing a triangle given the base length, height (AC = 75 mm),and one base angle (∠BAC = 75°).

6. Constructing a triangle given the base length and both base angles (∠ABC = 48° and ∠BAC = 32°).

TUTORIAL VIDEO CIRCLE ( DRAWING NO.5)

1. Constructing a circle passing through three given points.

2. Constructing an inscribed circle within a triangle.

3. Constructing a circumscribed circle.

4. Constructing a circumscribed circle outside a triangle.

TUTORIAL VIDEO POLYGON (DRAWING NO. 6,7& 8)

1. Constructing a regular pentagon given the side length

2. Constructing a regular pentagon inside a circle given the diameter.

3. Constructing a hexagon given the diameter.

4. Constructing a hexagon given the center dimension.

5. Constructing a regular heptagon given the constraint dimensions.

6. Constructing a regular octagon given the diagonal dimension.

PDP02903 - INTRODUCTION TO ENGINEERING DRAWING

4. Constructing a triangle given two side lengths (AB) & (AC = 60 mm) and a base angle (∠BAC = 60°).